How to Factory Reset Your Holosun EPS Carry

Wiki Article

Resetting your Holosun EPS Carry red dot sight back to factory settings can be a useful tool for troubleshooting issues or simply starting fresh. The process is fairly straightforward and only requires a few simple steps. Start by locating the reset button on the back of the sight. This small lever is often unmarked but can be easily identified by its position.

• Beginning a factory reset, you'll need to hold down the reset button for a designated length of approximately 3-5 seconds. You should see a blinking light on the sight indicating that the reset process is active.
• Once the process is complete, the indicator will return to its usual pattern.
• The sight itself is now restored to its original settings. You can then proceed with configuring it according to your needs.

Remember, always consult the user manual for specific instructions and details regarding your Holosun EPS Carry red dot sight.

Resetting Your Holosun EPS Carry to Original Settings

Need to Tweak your Holosun EPS Carry Optical back to its Starting configuration? It's Simple. Here's how:

First, ensure the Display is Activated. Then, locate the Control labeled "Mode".

Press and hold this Button for approximately 10 seconds.

You should Notice a series of Sequences on the Display. This indicates that the Holosun is now Restored to its Default configuration.

Once complete, release the Switch. Your Holosun EPS Carry is now Operational with all settings at their Initial values.

Resetting the Holosun EPS Carry Red Dot Sight

The Holosun EPS Carry Red dot sight is a popular choice for concealed carry applications due to its compact size and durable construction. However, like any optical device, it may require periodic adjustment. This can be easily accomplished by following these simple steps: First, find the adjustment screws on the side of the sight. These are typically located near the battery compartment. Using a small wrench, carefully turn the screws to fine-tune the point of impact. Begin by making minor adjustments and test fire the sight at various distances to ensure accuracy. Continue this process until you achieve a desired zeroing point.

• Remember that the adjustment screws can be easily damaged if overtightened, so use caution when turning them.
• Ensure that the battery is fresh and properly installed before making any adjustments.
• Should you encounter difficulty zeroing your sight, consult the manufacturer's instructions for further assistance or contact Holosun customer support.

Revert Factory Settings for Holosun EPS Carry

To reset your Holosun EPS Carry to its factory settings, you will need to navigate through the sight's menu system. First, activate the optic here by engaging the switch located on the side of the unit. Next, utilize the tactile buttons found on the holographic display to access the settings menu. Within the menu, locate the "Factory Reset" option and select it using the designated button. The EPS Carry will then undergo a reset sequence, which may take a few moments. Once complete, your sight will be restored to its default configuration.

• Note: During the reset process, all user-configured settings will be erased.

Clear Your Holosun EPS Carry Effortlessly

Need to get your Holosun EPS Carry back to factory settings? It's easier than you think! Here are the simple steps you need to follow:

First, turn off your sight. Then, find the tiny reset button on the side of the sight. Use a small object like a paperclip or a pin to press and activate the reset button for about 5 seconds. You'll know it worked when the display starts flashing.

• Wait
the sight to cycle through its startup sequence. This might take a few moments.
• You've successfully reset your Holosun EPS Carry to its original settings!

Reinitialize a Holosun EPS Carry Red Dot

Need to new configuration setup? Here's how to accomplish this to re-establish default settings your Holosun EPS Carry Red Dot.

First, make sure the red dot is switched on. Next, pinpoint the tiny button on the left/right side of the sight's housing/body. Maintain a continuous press on this button for at least 5 seconds/3 seconds. You should notice a flashing light/blinking indicator indicating that the reset process has begun/started. Keep holding/pressing the button until the light stops blinking/flashing. Stop pressing the button and your Holosun EPS Carry Red Dot is now completely reinitialized.

Report this wiki page